g/fur
Attached: 1cd1d58ed9c1f93b4871844ff9e40221.png (1065x600, 278.04K)
g/fur
first
third?
yusss
okee
You got it!
I was still ver disappointed
I want to go back to the happy times of 2011 that I saw in the dream and instead I wake up and find myself in 2022
Had perogi were tasty
I rarely remember dreams
though last night I was fishing in mine
a
oof 2 off again
e
I hate fishing
but then again the last time I went fishing I was about 7 and my dad beat me for getting the line stuck on a rock while reeling it in
i
AAAAAAAAAAAAAo
My dad didn't beat me while we fished so probably why I like it
Fishing dreams are weird, its like fishing in jello and you cant seem to reel anything in
o.o
uncool
why did I get stuck with a deadbeat
I remember catching a puffer fish from a pond
Though I don't remember actually reeling it in
idunno, least you're with your bf now
boop
my dad changed for the better eventually but I always feel uneasy being in the same room as him
HEY U BOOPED ME THAT'S MEAN
So did mine but he was already pretty good
Sucks you gotta deal with that
you booped me more (:
not at this point, you've gone mad with power :/
brushie brushie brush
clean your dergs
sorry :(
What if no dergs?
go down to the derg store and buy a litter
That sounds like a lot of responsibility for a whole litter of dergs
and money
Something something about magic and invisibility.
What if they are larger than a toothbrush?
dely speed up my pcb etching
responsibility is good it builds character
whatre you going to name your dergs
buy bigger toofbrush
no too messy just use pcbway it's fast as fuck
How can I brush my dergs if I can't find them?
heat and fluid movement helps. make it swirl around or have a fan move the surface liquid. Just be careful with splashing.
But what about the money it takes for all them dergs!
takes too long and i already have it in the etch bath
i was gonna make something to agitate it but im too lazy i just swirl it every 20 mins or so
start slangin dope
The same if you cant find your cat. Check the sleeping spots, get some food out or a box and wait a bit.
I think that's irresponsible to do when I don't have a litter of dergs yet
I don't think there was a time I couldn't find my old cat, though if he could turn invisible I'm sure that would make it quite hard to find
I've been etching with iron III oxide and it sometimes took forever and left a layer on the board of residue or went too fast on the edges.
But it has been 7-15min everytime.
Now i don't bother with the chem and buy it for 4 bucks from china.
has to be done by next week and im not paying express shipping
it've been almost 2 hours and only the edges have been eaten away
going on a walk
later gay bois
gronk
How was run?
good, chill and wet
Then diy it is.
Had the same with the first trys. Are you sure you got the illumination right and its unused etchant?
If it started etching, it left some black powder on the board. It stopped etching the copper under that residue so i always swirled it around. But that probably exposed the corners to more fresh stuff.
welcome back
its not developed i'm doing it with a sharpie, its working fine from what i can see just taking forever to get in to the middle, i should have sanded the board a little to get any protective shit off but wasn't really thinking
enjoy
hi
yea too long
i always use jlc which will take too long and im not paying for the faster postage like i said
its for a tube amp, most stuff i just soldered directly to the tube sockets but some of it needs to be somewhere else
Thats also possible.
Most boards nowdays come with a protective film on top to avoid having the copper go green in the air. There might be oil or glue left. Some have photoresist already applied.
If you have an old toothbrush, gently go over the board then. That should be soft enough to not scratch away the sharpie but get things going. Just make sure to clean and dispose it right.
And if that fails, just have the cnc scratch the negative out of it. The copper is 35µm and the board is 1,6mm thick for most boards.
Just a fair warning with the toothbrush: That splashes tiny droplets and you have to go very slow.
aa
are we talking about dragon brushing techniques
hi hun
he got nice hair
Foxy!
If you keep the chemicals away, its basically the same
Heya borbs!
how you be hun?
Wazman!
how are doing today cuter?
heya opros how are you?