How do I get rid of this sticker residue Yea Forums?

How do I get rid of this sticker residue Yea Forums?

Attached: image.jpg (4032x3024, 2.35M)

Soap and water?

Or gasoline.

lighter fluid

Wouldn’t that ruin the finish (not that I’m bothered THAT much)

In the oven for about 20 minutes at 300 degrees. Of course take the hardware neck etc off first.

If you're serious it's strip to pieces, paint stripper , prime then paint.

Peanutbutter.

cooking oil and baking soda, let it hang out for a few minutes and wipe it away with a cloth

New set of Seymour Duncans ...

I need new pickups but I’m broke af

That’s way too much effort, and I don’t have the right tools and I don’t wanna ruin the neck

this or windex.

Gotoh tuning pegs and tail piece.

BLAST IT WITH PISS

Desperate need for new tuning pegs I’m missing a screw

Attached: image.jpg (4032x3024, 1.69M)

Attached: 0069960D-4C45-4F4D-8C10-9864A359987E.jpg (1000x1000, 77K)

It's a fun thing about cheap knock offs. Just $350 of new top quality components and it will play as good as the $1,200 'we-saw-you-coming' signature model.

was going to post this. didn't think Yea Forums was this full of third-worlders who have never heard of goo gone

not at all, unless you light it
your local guitar shop will have a bag of those

this is actually ok for some surfaces, but its pretty strong and I have seen it damage stuff.

It plays pretty decent as is
The neck being sanded down wouldn’t hurt and new pickups would be nice but not necessary the tuning pegs cause some rattle but it’s nothing especially bad

i hate trip fags but this

I’m a Brit fag and I’ve never seen this in stores

just put another sticker over it

its just orange oil, essentially

Dont listen to this retard its 400 degrees

It looks a little better now

Attached: image.jpg (4032x3024, 2.03M)

another go should have it. What did you use?
unfortunately the scratches arent going to come out without sanding and refinishing. there are scratch coverup products but anything i have tried just sucks

white spirit

Yeah the scratches are bad, I seriously regret the carvings and im gonna wait until it goes naturally now, i used soap and water and I’m praying to god nothing got into the electronics

electronics are on the other side, unless you put it in the tub

Nail polish remover dapped onto a paper towl

Would rubbing alcohol work

There’s a cavity where you can access the soldering and shit

Attached: image.jpg (4032x3024, 1.66M)

im joking user,
unless you submersed it, it should be ok. probably yeah

I might try some hand sanitizer to get rid of the stickiness but the actual residue is gone I regret sticker bombing it I should of stuck it on my amp instead

isopropyl alcohol, lighter fluid, acetone, even windex (ammonia)
i dont know if purell has enough alcohol in it

It’s more than hand wash but probably less than those products but it’s the only thing lying about

I use this on my arse

dont want to believe this, but trips...

Don't worry about the scratches.

Attached: download.jpg (466x306, 35K)

I get that normal wear and tear is gonna happen but I might refinish it later on when I have a higher budget bc it’s not a very good finish in the first place

>bolt action les paul

Attached: 1495645059909.png (849x465, 376K)

It’s an epiphone

>bolt action les paul
holy shit

Attached: TRA5rtiv_400x400.jpg (240x240, 13K)

If I break the neck I can easily get a new neck unlike you virgins

Dealt with this before. Spray some WD40 onto it and let it sit for a couple minutes. It'll peel right off.

Attached: 1421413976415.jpg (540x720, 168K)

who cares. Fenders are all bolt ons

>bolt action les paul

Attached: laff 1.gif (200x154, 935K)